jackieleehome

回覆 9# 高登阿伯


    haha. thank you..  but i think i will order some filament from this 3dxtech.....

http://www.3dxtech.com/carbon-fiber-filament/
or
http://www.3dxtech.com/carbon-nanotube-filament/
or
http://www.3dxtech.com/abs-nylon-alloy-filament/

or buy all in 200G or 3Kg. haha  

but about the Ziplock Mylar Pouch, is it can i buy it from china?

jackieleehome

回覆  jackieleehome

The maker said the filament contains continuous  carbon fibre inside, but I do ...
高登阿伯 發表於 2015-1-19 11:41

    as i am thinking is why they need to use Nylon in the outter.

Super169

回覆  jackieleehome

The maker said the filament contains continuous  carbon fibre inside, but I do ...
高登阿伯 發表於 2015-1-19 11:41

想問個傻瓜問題, 普通既 fibre 係咪都係熔左拉絲既?

jackieleehome

回覆 13# Super169


炭纖 can't.. sorry my mis·take

Super169

as i am thinking is why they need to use Nylon in the outter.
jackieleehome 發表於 2015-1-19 11:47

可能 打印出黎結合得唔夠好, 外面包層膠穩陣 D , 同埋外觀好睇 D 掛.

Super169

回覆  Super169


炭纖 can't.. sorry my mis·take
jackieleehome 發表於 2015-1-19 11:55

oic, 咁即係如果用  炭纖 每一 part 就要一條絲直落再切開?  又好似無乜可能.
另外延續個傻瓜問題, 如果本身唔係拉絲, 一條長長既炭纖係點做既?  我只係傻瓜瓜諗緊, 佢又無可能模擬番本身炭纖既製造過程去打印....不過, 我完全唔知本身係點做既.

jackieleehome

回覆 16# Super169


    haha. but Graphite can... and very cheap.. in china.

http://www.timesnano.com/en/product.php?prt=3,36,65

jackieleehome

oic, 咁即係如果用  炭纖 每一 part 就要一條絲直落再切開?  又好似無乜可能.
另外延續個傻瓜問題, 如果 ...
Super169 發表於 2015-1-19 12:08

if need cut by place, base on logic may be can take the laser in the extruder, then cut, but... the point is carbon fiber made by layer by layer unless they use the nanotube

ma_hty

回覆 9# 高登阿伯

> The junction between filaments do not improved on the paper at least.

同感


> ...  fibre inside, but I don't think its product strength is not comparable to traditional carbon fibre counterpart, ...

我估這是筆誤吧, 兩次 NOT, 意思就反了.
I don't think ... is comparable to ... <= okay, 意思是 前者功能較差
I think ... is not comparable to ... <= okay, 意思也是 前者功能較差

I don't think ... is not comparable ... <= 意思就變成了 兩者功能相若, 而且同一個意思 用兩次 NOT, 文法也不對了.  (英語老師) => (哎呀...) (嘩喳~~) => (K.O.)

Super169

if need cut by place, base on logic may be can take the laser in the extruder, then cut, but... t ...
jackieleehome 發表於 2015-1-19 12:12

oic, 咁 nanotube 係咪會無  graphite  咁硬淨?
我估 nanotube 都應該比 ABS 硬淨好多掛...其實家陣 ABS 印出黎, 都已經幾硬淨下.  當然, 當工具用就更係唔得, 表面好易凹.
不過, 如果佢打印完表面都要加層膠,當工具用都只可以好大件...好似佢隻士巴拿咁.  否則, 我諗 10mm 既都未必得, 一扭既話, 內部夠硬, 但外層會凹, 好易打滑.