返回列表 發帖
chancho

Rank: 3Rank: 3Rank: 3
1# 跳轉到 » 倒序看帖
打印
tT
發表於 2016-3-18 14:49 | 只看該作者

n3150 problem follow up

i don't know if i solve the "wouldn't boot" problem or not. i use another harddisk and installed archlinux with systemd-boot as boot loader. now the system can boot (i can see the light blink). however, my router did not see that server. so i disconnect the harddisk and exam the journal log.
here is the reference about the lan port :
  1. Mar 16 17:08:39 Server2 kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
  2. Mar 16 17:08:39 Server2 kernel: r8169 0000:03:00.0 eth0: RTL8168g/8111g at 0xffffc90000644000, d0:50:99:9b:5f:3e, XID 0c000800 IRQ 122
  3. Mar 16 17:08:39 Server2 kernel: r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
  4. Mar 16 17:08:39 Server2 kernel: r8169 0000:03:00.0 enp3s0: renamed from eth0
  5. Mar 16 17:08:42 Server2 kernel: r8169 0000:03:00.0 enp3s0: link down
  6. Mar 16 17:08:42 Server2 kernel: r8169 0000:03:00.0 enp3s0: link down
複製代碼
however, when the harddisk is connected to another motherboard with monitor (and everything) attached. the log is :
  1. Mar 18 22:03:25 Server2 kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
  2. Mar 18 22:03:25 Server2 kernel: r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
  3. Mar 18 22:03:25 Server2 kernel: r8169 0000:03:00.0 eth0: RTL8168f/8111f at 0xffffc9000065a000, 60:a4:4c:38:f7:10, XID 08000800 IRQ 29
  4. Mar 18 22:03:25 Server2 kernel: r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
  5. Mar 18 22:03:26 Server2 kernel: r8169 0000:03:00.0 enp3s0: renamed from eth0
  6. Mar 18 22:03:31 Server2 kernel: r8169 0000:03:00.0 enp3s0: link down
  7. Mar 18 22:03:31 Server2 kernel: r8169 0000:03:00.0 enp3s0: link down
  8. Mar 18 22:03:33 Server2 kernel: r8169 0000:03:00.0 enp3s0: link up
複製代碼
it can get a static ip from router.
收藏 分享

0

cal22cal

Rank: 3Rank: 3Rank: 3
2#
發表於 2016-3-18 16:30 | 只看該作者
  1. harddisk is connected to another motherboard
複製代碼

Suggestions:-
1. put the hdd back to n3150 & make sure the cable is ok.
2. connect to a monitor
3. login as root
4. ip link set enp3s0 up ... (u can chage it back to eth0 by kernel boot command)
5. chk any ip address by command.
https://wiki.archlinux.org/index ... _network_interfaces
6. if still no dice, usually, it is the nic driver problem
http://askubuntu.com/questions/5 ... -14-04-after-update
ethtool -s enp3s0 autoneg off  (might fix that)

pls post the o/p of  lspci -v | grep -i -A20 rtl

TOP

返回列表