有無 ching 識得改 KISSlicer 既 setting 比 閃豬用?

Super169

之前件野印唔夠硬淨, 聽 dtom 講大大試下用 KISSlicer (1.5.2.20) 切片, 改 0.2 比佢印.
我用 KISSlicer gen 左 豬code, default 用 T0 (右邊) 唔駛改, 即轉 x3g.
放入閃豬比佢印, 一開波個頭不斷郁, 好似停唔到咁, 可能番唔到屋企 (home).
成半分鐘都係咁在右後角"依依轟轟", 嚇得我即刻停左佢.
我諗應該係有 D 野 set 錯左, 就算轉番 0.4 都係一樣.

上網對過, printer 平台大細應該無錯 (225x145x150), 但係其他唔知有無錯.
唔知有無 ching 用過 KISSlicer 幫閃豬切片, 可唔可以教下我點  set.  唔該哂先.

我家陣既 setting 如下, 唔知點解一開始個頭不斷在右後方撞黎撞去.

下載 (27.86 KB)

2015-4-27 19:29

下載 (30.73 KB)

2015-4-27 19:29

下載 (25.22 KB)

2015-4-27 19:29

下載 (23.44 KB)

2015-4-27 19:29

下載 (23.04 KB)

2015-4-27 19:29

下載 (31.41 KB)

2015-4-27 19:29

下載 (15.34 KB)

2015-4-27 19:29

下載 (19.39 KB)

2015-4-27 19:29

下載 (14.68 KB)

2015-4-27 19:29

Super169

oh, 有人好似copy 左makerware 既 start code 改左入 KISSlicer, 下載左試緊, 好似怪怪地, 一開始兩個頭一齊加熱???
https://groups.google.com/forum/ ... DmtJL4/91s5x0IxW1QJ
可能要再對比下機王個設定既 gcode 改下.  因為佢家陣一開始, 個頭又走左去左前方, 即刻撞左前面既門.

.... 結果...衰式, 凌空打印......好在睇住佢印, 唔係就PK 了.  成舊膠痴住個頭, 仲要兩邊一齊加熱.

Super169

完全唔得添, 下載哂佢幾個 sample setting for replicator dual, 都係凌空打印.

有無 ching 識得點 set?

mming1106

我都想知，而家用慣了kisslicer，用番其他真係唔多識用

mming1106

凌空打印，試下改個z offset(例如-5)

Super169

我都想知，而家用慣了kisslicer，用番其他真係唔多識用
mming1106 發表於 2015-4-28 11:13

ching 你唔係用閃豬的嗎?  印象中你好似係改左金屬架的閃豬.  定係我攪錯左呢?
你用 KISSlicer 無問題嗎?

mming1106

sorry我講得唔清楚，
我意思係用慣了kisslicer係kossel道，
部閃豬好耐無掂過佢了，
我都想知閃豬用kisslicer既setting點set，
因為喜歡kisslicer gen gcode真係閃電咁快，
如果用到，到時可能會用番多D部閃豬
你硏究到一定要分享出來啊

menil

唔知依家仲有幾多人keep住部閃豬?
我一路用開Slic3r都冇咩問題,但佢單線程切片實在多麻煩
今日終於把心一橫試下kisslicer, 我直接將Slic3r setting搬過去, 初步都print到野
最主要係prefix同postfix個gcode

下載 (106.72 KB)

2016-11-20 15:17

下載 (114.69 KB)

2016-11-20 15:17

下載 (108.23 KB)

2016-11-20 15:19

下載 (50.51 KB)

2016-11-20 15:19

下載 (48.41 KB)

2016-11-20 15:19

menil

1. M127
   
2. T0; set primary extruder
   
3. M104 S180 T0;
   
4. M73 P0; enable show build progress
   
5. M103; disable RPM
   
6. G21; set units to mm
   
7. G162 X Y F6000; home XY axes maximum
   
8. G161 Z F9000; home Z axis minimum
   
9. G92 Z0; set Z to 0
   
10. M132 X Y Z A B; Recall stored home offsets
    
11. G90; set positioning to absolute
    
12. G1 Z30; move Z to waiting height
    
13. G1 X-95 Y-73 Z30 F14000; move to waiting position (front left corner of print bed)
    
14. G130 X0 Y0 A0 B0; set stepper motor vref to lower value while heating
    
15. M6 T0; wait for bed and extruder to heat up
    
16. G130 X127 Y127 A127 B127; set stepper motor vref to defaults
    
17. M108 T0 R3; set extruder speed
    
18. G90; use absolute coordinates
    
19. M320; acceleration enabled for all commands that follow
    
20. G1 Z0.2 F6000.000; move to first layer height
    
21. G1 X100 Y-73 F14000.000; move to front right corner of bed
    
22. G1 X-90 Y-73 E24 F2000.000; extrude a line of filament across the front edge of the bed
    
23. G4 P2000; wait for ooze to slow
    
24. G1 Z0 F6000.000; lower nozzle height to 0
    
25. G1 X-95; wipe nozzle
    
26. G1 Z0.2 F6000.000; set nozzle to first layer height
    
27. G1 F12000; ensure fast travel to first print move
    
28. G92 E0; set E to 0 again
    
29. M73 P0; reset build progress to 0

複製代碼

下載 (89.44 KB)

2016-11-20 15:23

1. M73 P100 ; end build progress
   
2. G0 Z155
   
3. G162 X Y F2500; home X and Y axes
   
4. M18; disable all stepper motors
   
5. M109 S0 T0; set bed temperature to 0
   
6. M70 P5; Display "We <3 Making Things!" message
   
7. M72 P1; Play Ta-Da song

複製代碼

下載 (98.88 KB)

2016-11-20 15:24

效果好似好過Slic3r少少

下載 (146.56 KB)

2016-11-20 15:25

下載 (146.86 KB)

2016-11-20 15:26

menil

依家我想搞埋個support, 有冇ching分想下setting?