Board logo

標題: Enzotech 2隻CPU Block的簡測 [打印本頁]

作者: amoslee    時間: 2009-6-22 02:09     標題: Enzotech 2隻CPU Block的簡測

由於得到Sunderstan C Hing的幫助,得到了1個:


於是便於換Block前,把舊的Block做了個簡單的測試。
用作測試的Block是:
Enzotech的SCW-Rev. A及 Luna Rev. A




測試方法:
i7 920 (c0) OC至4.0GHz (21 X 191Hz),用orthos SP2004燒5分鐘,觀察其CPU的溫度。
所用的設備如下:
D5水泵+EK 增流Top
AS5散熱膏
4分喉及射咀
自制大水塘水箱
BlackIce 240 + 雙邊紅蝠
Loop : D5 ->BlackIce240 -> CPU Block ->水箱 ->back to D5



結果: (CPU0、CPU1、CPU2及CPU3的溫度)
SCW-Rev. A
71C、71C、68C、67C
Luna Rev. A
78C、78C、74C、74C

SCW-Rev. A比Luna Rev. A低6~7C!!!


有少少驚訝,於是再做多1次同樣的測試,結果:
SCW-Rev. A
68C、70C、65C、67C



Luna Rev. A
76C、76C、72C、72C



(溫度圖save咗係第2部機到,要遲D先才以post上來,sorry )
估唔到會有這麼大的分別,而且仲諗住新model會比舊model好添...
同時,亦觀察到SCW-Rev. A的水阻比較大,但跟目前這個配置卻反而得出比較好的表現。
請各位C Hing指教及討論,Thank You!

多謝收看

[ 本帖最後由 amoslee 於 2009-6-25 20:10 編輯 ]
作者: wonderful    時間: 2009-6-22 02:53

may I know the room temperature?
THX CHING!
作者: amoslee    時間: 2009-6-22 09:35

原帖由 wonderful 於 2009-6-22 02:53 發表
may I know the room temperature?
THX CHING!

當時室溫(有開冷氣)大約是23、24度左右,冷氣風口沒有連接或間接吹向部電腦。
4次的測試(SCW -> LUNA -> SCW -> LUNA)都是連續進行的。

[ 本帖最後由 amoslee 於 2009-6-22 09:37 編輯 ]
作者: sunderstan    時間: 2009-6-22 09:36

Thanks for sharing!
估唔到冷頭唔同溫度差別可以咁大??...
GTX240其實夠唔夠散架...........
作者: amoslee    時間: 2009-6-22 09:47

原帖由 sunderstan 於 2009-6-22 09:36 發表
Thanks for sharing!
估唔到冷頭唔同溫度差別可以咁大??...
GTX240其實夠唔夠散架...........

無錯,我都有D意外,雖然唔同頭,但係都出自同1牌子,分別會有咁大...

另外,有好多C Hing話BlackIce的fin太密,要用高速度fan或2邊都加fan先夠散熱。

好啦,下期小弟就做個冷排的比較啦。 (心目中想用240排,小弟的存貨只有TC、XSPC及BlackIce。亦可以試下用唔同風扇的,但小弟只得紅、白蝠、NoiceBlocker、Wing12),大家有乜意見?例如怎樣做、用什麼配置...等等。

[ 本帖最後由 amoslee 於 2009-6-22 09:48 編輯 ]
作者: aftergood    時間: 2009-6-22 10:47

紅蝠已經比wing 12大風
再上可能要kaze juni系列
不過用240排用在i7真係敏水d, 或者ching換粒d0可能比較好
作者: hangck    時間: 2009-6-22 10:58     標題: 回覆 6# 的帖子

其實個溫度巳經ok full load都係71c左右
就算换DO行4G FULL LOAD的話唔會差太遠

[ 本帖最後由 hangck 於 2009-6-22 11:07 編輯 ]
作者: mtx13579    時間: 2009-6-22 11:02

風扇用 coolermaster 2邊都加試下. Thanks.
作者: hangck    時間: 2009-6-22 11:03

Luna可能D銅柱唔夠高所以先差咁遠
睇完你TEST之後攪到我要轉冷頭
作者: hangck    時間: 2009-6-22 11:06

請問你新買隻水冷頭同SCW-Rev. A
FULL LOAD溫度差幾多到???
作者: aftergood    時間: 2009-6-22 11:09     標題: 回覆 7# 的帖子

可能我要求高la, 冷氣+4紅蝠 我覺得可以好d
我而家用緊u120 + avc pwm fan, 4g室溫full load 78-80, 諗緊上唔上水好

[ 本帖最後由 aftergood 於 2009-6-22 11:12 編輯 ]
作者: aftergood    時間: 2009-6-22 11:12

聽說最新隻phenix會比luna好,水阻會少d,等緊佢出場
作者: hangck    時間: 2009-6-22 11:15

原帖由 aftergood 於 2009-6-22 11:09 發表
可能我要求高la, 冷氣+4紅蝠 我覺得可以好d
我而家用緊u120 + avc pwm fan, 4g室溫full load 78-80, 諗緊上唔上水好

開埋冷氣又真係幾熱吓

[ 本帖最後由 hangck 於 2009-6-22 11:23 編輯 ]
作者: amoslee    時間: 2009-6-22 11:15

原帖由 aftergood 於 2009-6-22 10:47 發表
紅蝠已經比wing 12大風
再上可能要kaze juni系列
不過用240排用在i7真係敏水d, 或者ching換粒d0可能比較好

Thank you C Hing,
But this thread is just for a comparsion. When I real use this i7 920 (c0), I will use a better cooling system. (Or maybe to get a W3540 )
Thx.
作者: amoslee    時間: 2009-6-22 11:18

原帖由 mtx13579 於 2009-6-22 11:02 發表
風扇用 coolermaster 2邊都加試下. Thanks.

Now the "red bats" are already on both sides.
Coolermaster, which model are you thinking?

PS sorry, cannot type Chinese for the time being....
作者: amoslee    時間: 2009-6-22 11:23

原帖由 aftergood 於 2009-6-22 11:09 發表
可能我要求高la, 冷氣+4紅蝠 我覺得可以好d
我而家用緊u120 + avc pwm fan, 4g室溫full load 78-80, 諗緊上唔上水好

c0 / d0 cpu?
I guess, the c0 CO to 3.8G may even hotter than d0's 4.0G.
If my C0 goes to 3.8G only, there should be another 5~6C cooler.
That is, if SCW is used, full load MAYBE just 63~64C.
作者: amoslee    時間: 2009-6-22 11:27

原帖由 aftergood 於 2009-6-22 11:12 發表
聽說最新隻phenix會比luna好,水阻會少d,等緊佢出場

I heard that opposite!
Phenix's 水阻 is > than luna...
But as seen in my last little conclusion, the SWC's 水阻 is already > than the luna but it comes out produces a better performance than the luna!
we will see....
作者: aftergood    時間: 2009-6-22 11:33

依家用do
room temp


ac on at 26 degree



作者: amoslee    時間: 2009-6-22 11:48

原帖由 hangck 於 2009-6-22 11:06 發表
請問你新買隻水冷頭同SCW-Rev. A
FULL LOAD溫度差幾多到???

Because the new block has to change the back plate, so it will take some time to do the comparsion.
But meanwhile, you can watch the report from sunderstan C Hing.
http://www.hkepc.com/forum/viewthread.php?tid=1252095&extra=page%3D1&page=4
Only 60~65C ! Really good!!!

[ 本帖最後由 amoslee 於 2009-6-22 11:49 編輯 ]
作者: hangck    時間: 2009-6-22 12:03

原帖由 amoslee 於 2009-6-22 11:48 發表

Because the new block has to change the back plate, so it will take some time to do the comparsion.
But meanwhile, you can watch the report from sunderstan C Hing.
http://www.hkepc.com/ ...

個溫度低到....................不過應該同粒U低電壓有關1.2都冇
一分錢一分貸
作者: amoslee    時間: 2009-6-22 12:07

原帖由 hangck 於 2009-6-22 12:03 發表

個溫度低到....................不過應該同粒U低電壓有關1.2都冇
一分錢一分貸

W3520 = i7 920 d0
作者: hangck    時間: 2009-6-22 12:11

原帖由 amoslee 於 2009-6-22 12:07 發表

W3520 = i7 920 d0

XEON D CPU通常正D
作者: amoslee    時間: 2009-6-22 12:14

原帖由 hangck 於 2009-6-22 12:11 發表

XEON D CPU通常正D

yeap, that's why I am planning to get one, too!
作者: mtx13579    時間: 2009-6-22 12:19

原帖由 amoslee 於 2009-6-22 11:18 發表

Now the "red bats" are already on both sides.
Coolermaster, which model are you thinking?

PS sorry, cannot type Chinese for the time being....


cooler master 鐮刀 90CFM 2000RPM
作者: sunderstan    時間: 2009-6-22 12:22

我試過C0, D0, W3520
其實溫度上無乜分別
唔理你係唔係用低電, 超得高CPU主頻+UNCORE頻就會熱...
我仲等緊隻Black ICE GTX480...希望Performance會好d
水阻方面...其實如果你唔係拖得多野既話佢對效能影響唔大...
反而High restrictive既waterblock仲有機會造就到更好既performance呢

另外XEON唔係粒粒都好既
第一水既3844A709弱到無輪 又熱

[ 本帖最後由 sunderstan 於 2009-6-22 12:23 編輯 ]
作者: amoslee    時間: 2009-6-22 12:23

原帖由 mtx13579 於 2009-6-22 12:19 發表


cooler master 鐮刀 90CFM 2000RPM

I don't have that. But some C Hing said that it is very noisy. True?
作者: sunderstan    時間: 2009-6-22 12:33

原帖由 amoslee 於 2009-6-22 12:23 發表

I don't have that. But some C Hing said that it is very noisy. True?


ok啦 不過都唔夠我隻TT Thunderblade咁嘈 XDDD
(最近仲入左隻Delta AFB0812SHE 4900轉吹CPU供電 夠晒暴力!)
作者: amoslee    時間: 2009-6-22 12:42

原帖由 sunderstan 於 2009-6-22 12:33 發表


ok啦 不過都唔夠我隻TT Thunderblade咁嘈 XDDD
(最近仲入左隻Delta AFB0812SHE 4900轉吹CPU供電 夠晒暴力!)

我頂唔順嘈的風扇....頂籠1600rpm...
作者: hangck    時間: 2009-6-22 12:48

其實去到2000轉巳經好嘈
我個360排就係用2000轉
作者: mtx13579    時間: 2009-6-22 12:57

原帖由 amoslee 於 2009-6-22 12:23 發表

I don't have that. But some C Hing said that it is very noisy. True?


Not too noisy. Acceptable
作者: Seor    時間: 2009-6-22 13:35

係XS上看到過類似的成績,不過冇師兄的溫差咁大!
作者: amoslee    時間: 2009-6-22 14:02

原帖由 Seor 於 2009-6-22 13:35 發表
係XS上看到過類似的成績,不過冇師兄的溫差咁大!

小弟只是業餘的新手,換block、setup...等過程有乜做得唔好而導至結果有差異真不奇...
所以小弟特登重複多以求準確性。
其實小弟有cap圖的,但只因save咗係另1部機中固要遲D先可post上來,sorry!
作者: dannyctl    時間: 2009-6-22 15:03

相差幾大... 希望新嘢快D出...
作者: darrem    時間: 2009-6-22 15:17

提示: 作者被禁止或刪除 內容自動屏蔽
作者: amoslee    時間: 2009-6-22 15:23

原帖由 darrem 於 2009-6-22 15:17 發表
SCW-Rev. A係好
不過個面好易花

無錯,我果個都已經花晒啦....
作者: hamsterspeed    時間: 2009-6-22 15:29

原帖由 amoslee 於 2009-6-22 12:23 發表

I don't have that. But some C Hing said that it is very noisy. True?


is extremely noisy... i own 6 of them now sitting with dust
作者: freezewind    時間: 2009-6-22 22:34

早知之前唔買Luna
買SCW好過
作者: purplepaper    時間: 2009-6-23 02:08

原帖由 amoslee 於 2009-6-22 02:09 發表
由於得到Sunderstan C Hing的幫助,得到了1個:


於是便於換Block前,把舊的Block做了個簡單的測試。
用作測試的Block是:
Enzotech的SCW-Rev. A及 Luna Rev ...

師兄無次做既測試真係令小弟有所吸收.精彩精彩
作者: wonderful    時間: 2009-6-23 18:25

any test on heatkiller yet?
as I want to buy the POM version

作者: HiFiEddie    時間: 2009-6-23 23:50

果時又係揀呢兩款, LUNA貴D但效能仲差D, 初初貪佢有燈, 點知閃得咁衰, 都係熄左佢, 再買就唔好揀樣喇
作者: amoslee    時間: 2009-6-24 00:43

原帖由 purplepaper 於 2009-6-23 02:08 發表

師兄無次做既測試真係令小弟有所吸收.精彩精彩

多謝指教!
作者: amoslee    時間: 2009-6-24 00:46

原帖由 wonderful 於 2009-6-23 18:25 發表
any test on heatkiller yet?
as I want to buy the POM version

喱排未得閒..(又剛剛訂了個南北橋1體化block...)
HK 3.0效能可睇住sunderstan C Hing 的post先啦...
Sorry 呀!
http://www.hkepc.com/forum/viewthread.php?tid=1252095&extra=page%3D1&page=4
作者: wonderful    時間: 2009-6-24 00:49

原帖由 amoslee 於 2009-6-24 00:46 發表

喱排未得閒..(又剛剛訂了個南北橋1體化block...)
HK 3.0效能可睇住sunderstan C Hing 的post先啦...
Sorry 呀!
http://www.hkepc.com/forum/viewt ... page%3D1&page=4

no need to say sorry bro!!!!!!!!!!
作者: iloveskyline    時間: 2009-6-25 19:22

有機會我都想試試HK
作者: amoslee    時間: 2009-6-25 23:29

頭版加咗溫度圖。
多謝收看!





歡迎光臨 電腦領域 HKEPC Hardware (https://h0.hkepc.com/forum/) Powered by Discuz! 7.2